截至今天,92,434个运行小时, 螺杆直径为 190 mm.骨料 45050. L/D 22 带混合部件的阻隔螺杆。 计量距离900毫米位移25,520平方厘米。注射重量约18公 斤。 机器长度 17,418 mm 机器宽度 4,300 mm 机器高度 3436 mm 机器重量156~。 带油底壳 机器人ERC 125/0-F, / 建造年份 2006 灯霍拉布距离 2,000 x 1,600 毫米 (h / v) 夹紧板 2,900 x 2,500 mm (h / v) 最大板间距 3,800 mm 最小刀具安装高度 800 mm 最大刀具安装高度 1,800 mm 32 个加热区 芯拉 2 件固定面 / 4 件可移动面 针闭合/级联液压 10 件 针闭合/级联气动 8
提供: 恩格尔 Duo 940H/940 M/650 组合型 2011年 2x 毒蛇机器人 40 PS:机器从大约08 /2021开
Description: operating hours: approx. 33489 hrs. 3axis robot IMM type: Thermoset IMM serial number: 199583 clamping force: 180 tons production type: reflector screw type: BMC screw diameter: 35 mm barrel capacity: 154 cm3 max. spec. injection pressure: 1595/2177 max. stroke opening: 1050 mm max. mould thickness: 1050 mm min. mould thickness: 300 mm tie bars distance horizontal (mm): without tie bars tie bars distance vertical (mm): without tie bars locating ring size FH: 200 mm locating ring size MH: 200 mm max. ejector stroke: 180 mm max. ejector layout: 205 mm QMC type: manual total installed power: 80 kW  , please also have a look at the PDF document of this machine Approx. Onsite Dimension. (l x w x h): 1,950 x 5,200 x 2,900 mm, weight approx.: 14,200 kg
Description: 3axis robot IMM type: Thermoset IMM serial number: 199583 clamping force: 180 Tonnen production type: reflector screw type: BMC screw diameter: 35 mm barrel capacity: 154 cm3 max. spec. injection pressure: 1595/2177 max. stroke opening: 1050 mm max. mould thickness: 1250 mm min. mould thickness: 500 mm tie bars distance horizontal (mm): without tie bars tie bars distance vertical (mm): without tie bars locating ring size FH: 200 mm locating ring size MH: 200 mm max. ejector stroke: 180 mm max. ejector layout: 205 mm QMC type: manual total installed power: 80 kW injection valve missing  , please also have a look at the PDF document of this machine Approx. Onsite Dimension. (l x w x h): 1,950 x 5,200 x 2,900 mm, weight approx.: 14,200 kg
Gear motor, electric motor, three-phase motor, electric gear motor -Speed: 28 rpm -Power: 0.05 kW -Construction: B3 -Diameter shaft: Ø 12 mm -Protection class: IP 54 -Dimensions: 210/180/H120 mm -Weight: 4.5 kg
Gear motor, electric motor, electric gear motor, permanent magnet motor -Manufacturer: Engel, permanent magnet motor geared motor with brake -Engine:Type:GNM31650-G2.6-B5.2 -Voltage: 24V / 50W / 3000 rpm -Gear: Type G 2.6 i= 30:1 -Shaft: Ø10 x 23 mm -Protection class: IP54 -Brake: 0.5Nm -Dimensions: 250/125/H95 mm -Weight: 2.4 kg.
Description SILICONE PRESS Complete with REINHARDT-TECHNIK LSR 200 silicone pumping unit year 1998
Description Integrated robot: X: 1000 mm Y: 1400 mm Z: 2360 mm ROTATION 90 ° 1 BLOW (forceps) 2 EMPTY switchable
Description Mold heating 32 zones MACHINE SOLD IN THE STATE IN WHICH IT IS Missing monitor and floppy drive Missing tabs: - 2 AR281 cards - 3 TT081 boards - 1 PS244 / A card - AS141 connector (for closing transducer)
Description MACHINE WITH SERVO PUMP MOLD REDUCTION PLATE THICKNESS 70mm
Description MACHINE WITH SERVO PUMP MOLD REDUCTION PLATE THICKNESS 70mm
Description Euromap 67 robot interface plus adapter to euromap 12 hot chambers 4 zones
Description mold holder planes 740 X 680 New screw and barrell Sprue removal robot ENGEL mod. ER-USP 5 year:2006 pieces falling chute with waste selector
Description Compression machine with rotating table diam. 1600 n. 3 heating floors, dim. 590 x 650 Opening stroke: 400mm Minimum mold: 100mm
Description Compression machine with rotating table diam. 1600 n. 3 heating floors, dim. 590 x 650 Opening stroke: 400mm Minimum mold: 100mm
Description Compression machine with rotating table diam. 1600 n. 3 heating floors, dim. 590 x 650 Opening stroke: 400mm Minimum mold: 100mm
clamping force: 4.000 kN injection volume: 735 cm³ screw diameter: 60 mm platen size: 1.400 x 1.030 mm Condition: used, Specification: horizontal injection moulding machine, factory no: Injection unit 1: - screw diameter: 60 mm - metering stroke: 200 mm - Screw speed: 226 rpm - Injection flow: 351 cm³/sec - Injection volume: 735 cm³ - Spec. injection pressure: 1.489 bar - Spec. injection pressure increased: 2,011 bar Injection unit 2: - Screw diameter: 40 mm - Metering stroke: 140 mm - Screw speed: 400 rpm - Injection flow: 197 cm³/sec - Injection volume: 251 cm³ - Spec. injection pressure: 1.286 bar - Spec. injection pressure increased: 2.029 bar Clamping unit: - Clamping force max.: 4,000 kN - Clamping platens: 1,400 x 1030 mm - Opening stroke: 954 mm - Max. platen distance: 1,520 mm - Ejector stroke: 250 mm - Ejector forc ...
clamping force: 800 kN injection volume: 78 cm³ screw diameter: 25 mm platen size: 570 x 552 mm Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN08 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm - Control: CC 90-A0 Injection unit: - Injection volume max.: 78 cm³ - Injection weight max.: 90 g - Screw diameter: 25 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 400 rpm - Injection flow: 87 g/sec - Injection flow (increased): 64 g/sec - Specific injection pressure: 2400 bar - Nozzle stroke: ...
clamping force: 800 kN injection volume: 154 cm³ screw diameter: 35 mm platen size: 570 x 552 mm Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm Injection unit: - Injection volume max.: 154 cm³ - Injection weight max.: 156 g - Screw diameter: 35 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 320 rpm - Delivery flow: 35 g/sec - Injection flow: 148 g/sec - Injection flow (increased): 107 g/sec - Specific injection pressure: 1600 bar ...
clamping force: 450 kN injection volume: 99 cm³ screw diameter: 30 mm platen size: 860 x 320 mm closing stroke: 406 mm Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive ...
clamping force: 250 kN injection volume: 49 cm³ screw diameter: 25 mm platen size: 300 x 300 mm Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 1.300 kN injection volume: 106 / 43 cm³ screw diameter: 30 / 25 mm platen size: 850 x 750 mm daylight between platens - max.: 900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
锁模力:450 kN 注射量:135 cm³ 蠕变直径:35 mm 板尺寸:600 x 400 mm 条件:二手,规格 :用于TPE 的C型框架注塑机 - 使用的 夹紧装置: - 锁模力:450 kN - 加热板尺寸:600 x 400 mm - 滑动工作台:是 - 关闭方向:从下面 - 顶出器/升降器:向上 + Lo 注射单元: - 最大注射量:135 cm³ - 螺杆直径:35 mm - 连接值:3x 400 V,50 Hz - 重量约:5,500 kg 此广告的数据 fü,此广告是使用ModulMWS创建的 - LogoTech oHG的机器管理。
clamping force: 2000 kN injection volume: 251 cm³ screw diameter: 40 mm platen size: 1.050 x 900 mm daylight between platens - max.: 880 mm Condition: used, very good condition Specification: Vertical injection moulding machine, with rotary table injection unit: - screw diameter: 40 mm - injection volume: 251 cm³ - Injection flow: 244 cm³/sec - Spec. injection pressure: 1,300 bar - Spec. injection pressure increased: 2,020 bar - Nozzle stroke: 500 mm - Nozzle pressure: 51.9 kN Clamping unit: - Clamping force max.: 2,000 kN - Clamping platens hor. x vert. 820 x 459 mm - Max. platen distance: 880 mm - Opening stroke: 400 mm - Mould installation height: 480 mm - Ejector stroke: 105 mm Number of heating zones incl. nozzle: 4 - Heating power: 9.3 kW - Weight clamping unit: 11,000 kg - Weight injection unit: 3.500 kg - Wei ...
clamping force: 450 kN injection volume: 99 cm³ screw diameter: 30 mm platen size: 860 x 320 mm closing stroke: 406 mm Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive ...
锁模力: 1,750 kN 注射量: 318 cm³ 蜗杆直径: 45 mm 板尺寸: 700 x 700 mm 板间距 - 最大: 460 mm 条件: 二手,规格 : 卧式注塑机,注射 单元: - 螺杆直径: 45 mm - 螺杆长度 L/D: 20 - 喷雾体积: 318 cm³ - 注射重量 最大: 287 g - 规格喷雾压力:2,100 bar 夹紧装置: - 锁模力最大:1,750 kN - 夹紧板:700 x 700 mm - 开口行程最大:460 mm - 工具安装高度:150 mm - 工作时间:89217 h - 1x 抽芯 处理/机器人:ENGEL 本广告是使用 ModulMWS 创建的 - LogoTech oHG 的机器管理。
编号: 18092 制片人: 恩格尔 建造年份: 2001 锁模单元 锁模力:300吨 开启行程: 855 mm 压板尺寸(高 x 垂直): 1050 x 650 mm 注射单元 螺杆直径: 60 +35 mm 注射量: 735 +135 cm³ 注射重量: 662 + 122 g 注射压力: 1834 +1620 bar 测量和重量 尺寸: 7,75 x 2,35 x 2,6 m 机器重量: 25250 公
编号: 18255 赫斯特勒:恩格尔 建造年份:2004 锁模单元 锁模力:180吨 开启行程: 750 mm 拉杆之间的距离: 960 x830 mm 最小模具高度: 500 mm 开口宽度: 1250 mm 注射单元 螺杆直径: 45 mm 注射体积: 318 cm³ 注射重量: 302 g 注射压力: 1769/2360 bar 测量和重量 机器重量: 13500 公斤 机器人 生产商:威特曼 型号:W743 年份:2009
Clamping force: 7000kN, screw diameter: 40mm, screw speed: 300/min, metering stroke: 200mm, controls: Engel CC300, weight: 22t, operating hours: 3871h, with electric 6-station turntable, electric quick adjustment machine clamping platen moving side, two injection units, 2x 3-zone screw D45mm, 32 hot runner control zones, electric plasticising units and documentation.
Clamping force: 1600kN, weight: 9t, operational hours counter: 3638h, with Handling Robot ENGEL viper 20.
Closing force: 180t, weight: 12.2t, operational hours counter: 24,492h, with Handling Sepro S 5.35, fence, conveyor and documentation, an inspection is possible.
Clamping force: 275t, injection weight: 455g, cylinder diameter: 55mm, max. opening distance: 850mm, weight: 20t, operational hours counter: ca. 63,000h, including documentation, a set of new pumps and Handling GEIGER LR 16 EC, the handling needs overhauling.
Injection molding machine: clamping force: 5000kN, opening stroke: 1109mm, max. mold weight per plate/total: 5300kg/10600kg, drying time: 4.15s. Injection units: Unit 1: screw diameter: 90mm, injection flow: 623cm³/s, max. injection pressure: 2000bar. Unit 2: Screw diameter: 50mm, injection flow: 295cm³/s, max. injection pressure: 2000bar. Weight (without oil): Clamping unit: 33350 kg, injection unit: 9000 kg. ENGEL Viper 20 robot: max. manipulation weight: 17kg, max. vertical workpiece size: 600mm, travel X/Y/Z: 700mm/1300mm/3320mm. Total height of robot and machine: 4250mm, compact C-axis: pneumatic, torque: 30Nm, range: 0°-90°. Documentation available.
Weight: 9.1t, the machine is leaking and the control card is missing.