子类目
(三级类目)
生产厂家:
(品类: 109)
max. wheel diameter: 400 mmgear width: 75 mmmax. module: 0,5 min. module: 60 total power requirement: 25 kWweight of the machine ca.: 7 tdimensions of the machine ca.: mL O R E N Z (Germany)High Performance Automatic Gear ShaperModel LS 400 Year 1975 Serial No. 12 592 ______________________________________________________________________ ___________External gear, max. Ø 400 mm (possibly larger)Internal gear dia. 350 mmGear width, max. 75 mmModule range 0.5 - 6Length of stroke 82 mmAdjustment of stroke position 0 - 100 mmDistance between shaper spindle and machine body 250 mmSpindle taper MK 5No. of strokes, roughing/finishing process 118 - 1,000 per minTable size 400 mmTable bore 125 mmMounting height between table and shaper head 190 / 290 mmAxial tra ...
铣床槽对接头,铣头,CCCP / 苏联斯坦科 型号 1502编号:200 建造年份 1974行程尺寸:最大 60 mm冲程数:约 200 - 500 冲程/分钟刀架:12 x 17 mm,带夹紧板 孔间距机法兰板: 245 x 185 mm 安装孔: 17 mm 机器法兰板上的定心直径: 190 mm- 行程尺寸可通过偏心调节进行调节- 与普通垂直头一样,驱动器可以通过驱动器从机床齿 驱动器连续旋转,以定心直径为中心- 法兰板上的度数缩放+/- 45- 此槽对接头用法兰代替普通立式铣头(代替立式铣头 铣头的组装)重量:42 kg状况良好 来自同一台 STANKO 铣床的槽对接头库存号 58166 和立式铣头库存号 58164
圆度测试仪 品牌:泰勒霍布森 类型:泰利森3年建造:1974年操作说明书 计算器 数据备份光盘 所有信息无保 ... 更多信息
立式铣头、铣头、角铣头 CCCP / 苏联斯坦科 1905 型 型号: 393 建造年份 1974 刀架: MK4 孔间距 机器法兰板: 245 x 185 mm 安装孔: 17 mm 机器法兰板上的定心直径: 190 mm- 通过托架驱动,定心直径居中- 法兰板上的度数缩放 4x 90 可旋转- 角头上的度数缩放 +/-90 旋转重量: 65公斤状况良好同一台斯坦科铣床的槽对头轴承编号58 166和立式铣头轴承编号58164;使
文章编号: 01-08-002 制造商: Profile bending machine 一般状况良好 经过机械车间测试 出货时间:保留所有权利。 建造年份:约1975年 长x宽x高:约800x600x1000mm 重量:约150kg 控制:常规 最大弯曲能力(钢):约150x10mm 最大弯曲能力(不锈钢):约150x5mm 卷数:3 件 弯曲过程:向前/向后 滚轮:约100mm/75mm 下滚轮间距:约380mm 顶辊距离:约0-70mm 驱动功率:约2.0kW 可根据要求提供其他配件 价格和其他技术数据可根据要求提
max. wheel diameter: 400 mmgear width: 0 mmmodule: pinion diameter - max.: 254 mmaxial cross angle: 90 °total power requirement: 15 kWweight of the machine ca.: tdimensions of the machine ca.: mThis machine is very suitable for precision production testing of spiral and hypoid bevel gears with shaft angle 90°. The gear spindle is vertical and the pinion spindle is horizontal. The pinion cone distance can be adjusted while the machine is working in order to find the optimal mounting position whereby the gear is loaded with a preset torque. The axial pinion position can be adjusted until the quietest meshing position of the traction flank is found. Likewise, the thrust flank can be tested during the return run. Marking compound is sprayed on both sides of the teeth so the flank contact pattern can be seen. Working cycles, as well as the positioning in the tooth gap, are automatic ...
直径范围 10- 18 mm模具数量 4工位数 5切割长度 155 mm轴长 头下长度 125 mm输出 - 件/分钟 90压力 200至最大头直径 35 mm ... 更多信息