二手 KELLER 出售

酒窖 SMM 012.0 抽气鼓风机 直径 120/120mm 空气流量 700 Nm³/h 0.55kW

凯勒 SMM 016,0 抽气鼓风机 直径 160/160mm 空气流量 1200 Nm³/h 1.5kW

地窖 抽气鼓风机 1.8kW

容积流量 2，000 – 3，000 m³/h 声压级 < 75 dB 长/宽/高 1.4 米 / 1.4 米 / 2.0 米 重量 1，025 t 功率要求 7.5 kW

Description: Machine number: 502485 Operating voltage: 400 V Frequency: 50 Hz Connection: 5.5 kW Approx. Onsite Dimension. (l x w x h): 1,400 x 1,200 x 2,000 mm, weight approx.: 500 kg

sheet width: 480 mm plate thickness: 3 mm stations: 13 total power requirement: kW weight of the machine ca.: 11 t dimensions of the machine ca.: 15,x2 m Number of stations 13 Number of straightening stations 1 Waves 60 mm Center distance, horizontal 310 mm Center distance, vertical 110 - 250 mm Speed approx. 11 m / min. Connected load approx. 20 kW Uncoiler (without drive) - Coil- , inside 508/610 mm - Coil weight 3 t Flying hydraulic scissors Roller set for hat profile The techn. Data is manufacturer or operator information and therefore for us not binding. We reserve the right to make an interim sale, it applies exclusively our business and conditions of sale. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Type: Vario T 1.0 L originates from LVD lasercutting machine power: 2,2 kW

Single screw degassing extruder CFE-699-A-04 for polymers manufactured by KELLER (USA) and KOBE STEEL (Japan) under a DUPONT license. The extruder has the following parameters: Overall dimensions of the extruder, taking into account the gearbox and motor - length 12 meters, width -2.5 meters, height -1.5 meters, the total diameter of the casing with a heating-cooling jacket is 950 mm, the diameter of the screw is 600 mm, screw length -7800 mm. The average screw speed is 22-25 rpm. The total weight of the extruder without spare parts is 40 tons. The working pressure in the casing is up to 300 bar, the working temperature of heating the melt is up to 300 degrees. The casing of the extruder is heated by high temperature oil supplied to it. The average productivity of polymers is 50-100 tons per hour. The extruder is equipped with a parallel reducer of POWER-TECH INTERNATIONAL (FOOT-JONES)  ...

Two-roll corrugating machine - crimper, for the production of polyester staple fibers, manufactured by KELLER (USA) by order of KOBE STEEL (Japan). The width of the work rolls is 150 mm. It is equipped with a clamping pneumatic cylinder and a drive gearbox manufactured by SEISA REDUCTION GEARS with a capacity of 150 kW. Productivity is up to 50 tons / hour. Made of AISI 304 stainless steel. 4 pieces are available. The equipment was practically not used - an operating time of about 60 hours.

技术参数 主轴转速：1800 rpm 吸气：20 m3/min 电压 50 Hz 3x：400 伏 驱动电机（电机功率）：1.1 千瓦 功率：2.7 A 重量：100 kg 尺寸： 长度：800 mm 宽度：550 mm 高度：1100 mm

容量 （x）： 0 工艺应用： 0 其他信息： 0 技术数据 主轴转速： 2850 rpm 吸气： 1000 m3/h 电压 50 Hz 3x： 400 伏 驱动电机（电机功率）： 1.5 kW 尺寸： 长度：1200 mm 宽度：800 mm 高度：2300 mm

容量 （x）： 0 工艺应用： 0 其他信息： 0 技术数据 电压 50 Hz 3x： 400 伏 装 机功率： 0.55 千瓦 重量： 60 千克 尺寸： 长度： 650 mm 宽度： 500 mm 高度： 1100 mm