液压剪床 液压剪板机

工作长度 3050 mm，板厚 400N/mm² 至 12 mm 切割角度可调至最大2.5° 16 压紧装置 冲程频率 35 - 10 1/min 重量约 8500 kg 包括。 NC背挡料和自动调整 切割角度和切割间隙 脚踏开关，手动 液压操作的机器无需加油即可分配�

供应 24162 规格： - 最大工作宽度 3050 mm - 最大切割能力 - 400 N/m² 强度 6 mm - 在 700 N/m² 强度下 4 mm - 可调节切割角度 - 通过手柄调整切割间隙 - 液压压紧装置数量 14 pcs - 带定位控制的后挡料 AMADA 10 - 1000 mm - 前角止动器+支撑臂 - 冲程频率 12 - 32 每分钟 - 驱动 400 V / 12 kW - 工作台高度约。 800 毫米 - 空间要求包括后挡板，不带前支撑臂 -ca。 宽 3800 x 高 1950 x 深 3200 mm - 运输宽度约 2200 毫米 - 重量约 6000 千克 - 带： - E - 脚踏开关 - 钣金夹持 -莫特。物料输送带 - 切割长度调整 - 切割线照�

sheet width: 3050 mmplate thickness: 6,0 mmcutting angle: 0,5 - 3,0 °down holder: 18 Stückno. of strokes: 9 / 14 Hub/minback stop - adjustable: max. 750 mmControl: konv. engine output: 10,0 kWweight: 4800 kgrange L-W-H: 3750 x 1600 x 2450 mmFurnishing:- electro-hydraulic / slide-guided sheet metal shears- front control panel, left - easy to use- with electro-hydraulic cutting angle adjustment- with manual cutting gap adjustment, from the rear- electro-motorized back gauge 10-750 mm- with analogue position display + handwheel for fine adjustment- 1x extra long, robust side stop .. 3,000 mm- 1x extra long, robust support arm- 1x freely movable foot switch- front finger/encroachment protection- 2x EMERGENCY stop buttons at the front- User manual (PDF) Machine link:http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno =1008-9325333The data for this ad was created with ModulMWS  ...

板材宽度：3050 mm板材厚度：6 mm支架宽度：3100 mm后挡板 - 可调：750 mm切割角度调整：0.5 - 3.0 行程率：9 - 17 冲程/分钟地板上方的桌子高度：775 mm总功率要求：7.5 kW机器重量约：4.5吨机器尺寸 长 x 宽 x 高：3.75 x 1.65 x 1.7 m配件：电气器。后挡板，角度停止，工作台扩展，更 换刀数据fü，此广告是用ModulMWS创建的 - LogoTech oHG的机器管理�

液压剪板机 制造商大西洋 型号 ATS3000 建造年份 1996 最大切割厚度 6，0mm 切割长度 3050mm 机器上的新刀 此外，有2把刀加1个树桩，一旦新 机器功能齐全，4个月未通电 安舍格，提供流通和文件�

规格： - 最大工作宽度 3050 mm - 最大切割能力 St 40 6 mm - 切割角度可调 0,5 - 3 - 手动调整切割间隙 - 液压压紧装置数量 18 pcs -莫特。- 后挡料 10 - 750 mm - 前角止动器+支撑臂 - 行程速率取决于切割角度和切割长度 9 - 17 per/min - 液压驱动 400 V / 7.5 kW - 工作台高度 770 mm - 空间要求包括后挡板，不带前支撑臂 -ca。 宽 3750 x 高 1600 x 深 1650 毫米 - 重量约 4500 千克 - 与： - E. - 脚 - 开关 - 切割线照�

sheet width: 3050 mmplate thickness: 12,0 mm STplate thickness: 8,0 mm VAno. of strokes: 7 - 14 Hub/mindown holder: 18 Stückcutting angle: 0,5 - 3,0 °work height max.: 930 mmback stop - adjustable: 1000 mmNumber of working hours: 18.822 htotal power requirement: 22,5 kWweight: 8.500 kgrange L-W-H: 4180 x 2030 x 2210 mmFurnishing:- Robust hydraulic, link-guided guillotine shears- Electro-motor backgauge with analogue display Fine adjustment via hand wheel, front left- Control panel, front left- manual cutting gap adjustment, from behind- electro-hydraulic cutting angle adjustment- Front finger protection- Stable front support table- 1x side stop with T-slot and millimeter scale- 3x support arms- 1x free moving footswitch- User manual (PDF) Machine link :http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=100 8-9325234The data for this ad was created with ModulMWS - the sof ...

板材宽度：3050 mm板材厚度：12 mm支架宽度：3100 mm走廊上的工作台高度：900 mm切割角度调整：0.5 - 3 冲程：6 - 13 冲程/分钟后挡板 - 可调：1000 mm压下：18个油容量：350 l总功率要求：22.5 kW机器重量 约：8吨机器尺寸 长 x 宽 x 高：3.96 x 2.38 x 2.22 m配件：电气。后备考格，替换刀数据fü，这个广告 是用ModulMWS创建的 - LogoTech oHG的机器管理�

类型： ATSL 3013 制造：大西洋 建造年份/年：1992年 库存号： 0969 最大板材宽度的板材厚度/ 最大切割长度处厚度： 13 mm （ 低碳钢 ） 6 毫米 （ 不锈钢 / 高级钢） 切割长度： 3050 mm 重量/重量： 约 8.6 t 规格：逆止�

sheet width: 3050 mmplate thickness: 6.0 mmcutting angle: 0.5 - 3.0 °down holder: 18 Stückno. of strokes: 9 / 14 Hub/minback stop - adjustable: 750 mmControl: SC7p engine output: 10.0 kWweight: 4800 kgrange L-W-H: 3750 x 1600 x 2450 mm from a maintenance workshop well maintained condition - checked annually ()Furnishing:- electro-hydraulic sheet metal shears - backdrop-guided- ATLANTIC NC control unit - model SC7p Target / actual information about the motorized back gauge Manual positioning possible via handwheel Digital display for backgauge position electro-hydraulic cutting angle adjustment Adjustable retraction from the back gauge before the start of the cut Front left control unit- electro-motorized back gauge 10-750 mm- manual cutting gap adjustment, from the rear- 1x front side stop, with mm scale- 3x front support arms- 1x freely movable foot switch- Finger protection at the fr ...

水润。桌子剪刀，二手，准备在电下演示       液压采煤机，使用，在动力下，准备运行 类型/ 型号： XTSL 3016 法布尔/ 品牌 ： 大西洋 建设年份： 1993 板材厚度最大/板材宽度最大/ 最大切割长度厚度： 16 mm （ 低碳钢 ） 12 毫米 （ 不锈钢 / 高级钢） 切割长度： 3100 mm 重量： 约 14 t 规格：逆止�

sheet width: 3050 mmplate thickness: 6 mmControl: SC5 back stop - adjustable: 750 mmtotal power requirement: 7,5 kWweight of the machine ca.: 4,5 tdimensions of the machine ca.: LTH 3,8 x 2,5 x 1,7 m- motorized backgauge- Electric cutting gap adjustment- electric Cutting angle adjustment- Footswitch- Front support arms 2.60 m.- pneumatic lifting device- Spare knife- Rear area monitoring optical sensorThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2560 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 2600 mmdown holder: 12 Stückno. of strokes: 20 Hub/minoil volume: 160 ltr.cutting angle: 1.6 °Control: ELGO TYP 71 back stop - adjustable: max. 750 mmtotal power requirement: 11.37 kWweight: 3800 kgrange L-W-H: 3030 x 1910 x 1510 mm Current new price approx. 37.000 euros Special price on requestFurnishing:- Robust electric hydraulic swing cutter- Elgo type 71 digital control unit Driving back stop x = 750 mm play -free ball circuit spindle for back attack Speed 100 mm/sec- 1x side stop with a t-groove, flip stop and millimeter scale- 2x front reversing arms- Electrical cutting length limit Cutting length limitation to increase the number of lifts/min.- Manual interpretation- front finger/intervention protection- TIP operation with push buttons on the switch on the left- original operatin ...

sheet width: 3060 mmplate thickness: 8.0 mmthickness at Niro-steel: 6.0 mmdistance between columns: 3100 mmdown holder: 16 Stückno. of strokes: 10 Hub/minoil volume: 160 ltr.cutting angle: 1.6 °Number of working hours: ca. 2.100 hback stop - adjustable: 6.0 - 750 mmControl: total power requirement: 18.5 kWweight: 6300 kgrange L-W-H: 3900 x 2300 x 1630 mm from a maintenance workshop hardly used - only approx. 2.100 operating hours () New price approx. 40.000 euros Special price on requestFurnishing:- electro-hydraulic swing cutting shears- ELGO digital display model P9521, for electric back gauge Travel distance back gauge X = 750 mm Backlash-free ball screw for back gauge Back gauge beam can be automatically tilted up to maximum position for pushing extra long sheets through Travel speed 100 mm/sec- 1x stable side stop with T-slot, flip stop and millimeter scale- 2x front, stable supp ...

供应 22408 规格： - 最大工作宽度 3050 mm - 最大切割能力 St 40 10 mm - 投影 270 mm -切割角度 - 手动调整间隙 - 液压压紧装置数量 16 个 - 机械后挡料 20 - 650 mm - 前角挡块 + 支撑臂 - 行程速率取决于切割角度和切割长度 7 - 12 每分钟/分钟 - 液压驱动 400 V / 22 kW - 工作台高度约 820 毫米 - 空间要求，包括后挡板，不带前支撑臂 -ca. 宽 3850 x 高 2000 x 深 2000 mm - 约重 8500 公斤 - 带： - 电动脚踏开关 - 切割线照�

sheet width: 3060 mmplate thickness: 10,0 mmthickness at Niro-steel: 6,0 mmback stop - adjustable: 5,0 - 1000 mmwork height max.: ca. 820 mmcutting angle: 2,4 °stroke: 7-12 p/min.down holder: 14 Stückoperating pressure: 360 barControl: ELGO oil volume: 200 ltr.voltage: 400 Vtotal power requirement: 22,0 kWweight: 9000 kgrange L-W-H: 4000 x 2300 x 2000 mmFurnishing :- robust / hydraulic swing shears- with ELGO digital control- electric backgauge 5.0 - 1,000 mm zero-backlash ball screw for backgauge Backstop beam can be automatically tilted up in max. position Speed 100mm/sec- 1x side stop- 2x front support arms- electrical cutting length limitation Cutting length limitation to increase the number of strokes/min.- manual cutting gap adjustment centrally operated on the right side stand- Machine side stand with overhang- Front support plates with ball rollers- front finger protection- Tip ...

贝耶勒 VE 6.5 x 4080 液压。断头台剪， 建造年份 1993， 切割宽度 4，000 mm， 背景引导刀杆， 自动。切割/角度调整埃尔马克桑， 板材厚度可达 10 mm， 年度安全检查， 配件备用刀具�

供应 22537 规格： - 工作宽度 4040 mm - 切割能力 St 40 6 mm - 切割角度水文可调 0.5 - 3 - 切割间隙调节液压。 - 液压压紧装置数量 22 个 -莫特。– 带定位控制装置的后挡料 10 - 1000 mm - 前角挡块 + 支撑臂 - 行程速率取决于切割角度和切割长度 7 - 15 p/min - 液压驱动 400 V / 7.5 kW - 气动连接 6 巴 - 工作台高度 770 mm - 大约需要空间 宽 5100 x 高 2250 x 深 2150 mm - 约重 9000 公斤 - 带： - 电动脚踏开关 - 切割线照明 - 气动支撑的钣金提�

液压剪切机 COMESSA CP 316 加工能力： 3000 x 16 mm 后档距行程： 1000 mm 喉深： 500 mm 电机功率：35 CV 可调刀片 4 切割刀片 电压：380 V 尺寸（长 x 宽 x 高）：3500 x 2200 x 2400 mm 重量： 16 T

板材宽度：3100 mm板材厚度：20 mm支架宽度：mm总功率要求：kW机器重量约：t空间要求 约：m轴承数2110009机器类型 面板剪切机使达利型 GS 3100/20建造年份 1987控制型 带电停止板宽度 3100 mm板材厚度 20 mm该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理�

工作宽度： 4100 mm 片材厚度： 6 毫米 投影： 100 mm 后挡风量： 0 - 1000 mm 驱动功率：18.5 kW 空间要求：4600 x 2200 x 1950 mm 重量： 11000 kg

-展示机械- 德瑞泰克 Practica CNC液压剪板机 3050 x 20 mm 可用 型号 VAC-20 x 3050 mm 液压库利森引导的断头台剪板机，设计坚固 Cybelec CybTouch 8 控制器 后挡料 1000 mm，可折叠 角挡 1000mm 支撑臂 1000 mm 用于切割具有 4 个切削刃的 VA 材料的刀具 带滚珠的支撑台 DWSQ0E 自动调整切割角度和切割间隙 行政长官

液压剪刀 - 订购机（交货时间约 10-14 周） - 包括脚踏开关、触摸屏、带光栅监控的后部安装室、� ��动/电动切割间隙、自动/电动切割角度、液压压紧、 MOT后挡料深度可达 1000 mm -插图相似- 液压剪板机 - 订购机（交货时间约 10-14 周） - 包括脚踏开关、触摸屏、带光栅监控的后部设置区域� ��自动/电动切割间隙、自动/电动切割角度、液压压紧 、MOT。后挡料可达 1000 mm -图片相似-

3000x8型剪�

液压剪刀 - 订购机（交货时间约 10-14 周） - 包括脚踏开关、触摸屏、带光栅监控的后部安装室、� ��动/电动切割间隙、自动/电动切割角度、液压压紧、 MOT后挡料深度可达 1000 mm -插图相似- 液压剪板机 - 订购机（交货时间约 10-14 周） - 包括脚踏开关、触摸屏、带光栅监控的后部设置区域� ��自动/电动切割间隙、自动/电动切割角度、液压压紧 、MOT。后挡料可达 1000 mm -图片相似-

板材宽度：3000毫米板材厚度：10毫米支架宽度：毫米� ��功率要求：kW机器重量约：9.8吨空间要求约：4.15 x 3.55 x 2米品牌：杜尔马类型：DHGM 3010建造年份：2002刀长：3，000毫米板材厚度：10毫米� �动逆止器机器尺寸（lxbxh）：4，150 x 3，550 x 2，000毫米机器重量：9，800公斤该广告的数据是使用� �态MWS创建的 - 标识科技oHG的机器管理�

sheet width: 3100 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 3120 mmdown holder: 16 Stückoil volume: 200 ltr.cutting angle: 1° 30 no. of strokes: 15 Hub/mincontrol: ENC 100 table width: 500 mmthroat: 50.0 mmNumber of working hours: 912 htotal power requirement: 15.0 KWweight: 7650 kgrange L-W-H: 3810 x 2200 x 2050 mm from a maintenance workshop () very good / well-maintained condition (as new) with only 912 operating hours current new price ~ 45.000 euros Special price on request-------------------------------------------------- NC electro-hydraulic swing cutting shear with DURMA ENC 100M control manual cutting gap adjustment Incl. pneumatic sheet metal holding device for thin sheet metal cuts-------------------------------------------------- Furnishing:- robust electro-hydraulic swing cutting shears- including DURMA ENC 100M NC control unit Backg ...

sheet width: 3100 mmplate thickness: 10,0 mmthickness at Niro-steel: 6,0 mmdistance between columns: 3120 mmdown holder: 16 Stückoil volume: 200 ltr.cutting angle: 1°50 no. of strokes: 13 Hub/mincontrol: ENC 100M table width: 580 mmthroat: 50,0 mmtotal power requirement: 22,0 KWweight: 9300 kgrange L-W-H: 4200 x 2250 x 2100 mm from a maintenance workshop New price ~ 55.000 euros-------------------------------------------------- robust electro-hydraulic oscillating shears with DURMA ENC 100M NC control Manual cutting gap adjustment, via eccentric-------------------------------------------------- Furnishing:- electro-hydraulic oscillating shears- with DURMA ENC 100M control Backgauge preselection - X axis Number of pieces Cutting length limitation Swivel control, left front- motorized backgauge, travel = 1.000 mm (X axis) on ball screws Travel speed 200 mm/sec.- Manual cutting gap adjust ...

最大切割长度：3080 mm 切割时最大板材厚度： 6 mm 最大切割角度：2个 总功率要求：11 kW 后挡风： 1000 mm 机器高度 ： 1950 mm 机器长度： 4100 mm 机器宽度：2050/3650 mm 机器重量：7980 kg

供应 21001 规格： - 工作宽度 3050 mm - 切割能力 St 40 10 mm - 切割角度 2 - 手动调整间隙 - 液压压紧装置数量 17 个 - 电机 - 后挡料 20 - 1000 mm - 前角挡块 + 支撑臂 - 液压驱动 400 V / 22 kW - 工作台高度约 900 毫米 - 空间要求，包括后挡料，不带前支撑臂 -ca. 宽 3900 x 高 1950 x 深 2250 mm - 约重 7800 公斤 - 带： - 电动脚踏开关 - 切割线照明 - - 切割长度预�

最大切割长度： 1050 mm 最大板材厚度：3 mm 钢 电动后挡料可达 1000 mm，可通过手轮进行微调 剪切角调整 刀锋利 操作说明 重量： 约 1400 kg

板材宽度： 1050 mm 板厚： 3,00 mm 柱间距离：mm 总功率要求：kW 机器重量 ca.： 1,40 t机器尺寸 ca.： m电动后挡料可达 1000 mm，可通过手轮进行微调 剪切角调整磨刀操作手�

sheet width: / mmplate thickness: / mmdistance between columns: / mmManufacturer: EHTType: TSS 20-25Year of construction: 1994Max. Cutting length: 2250 mmMax. Sheet thickness: 20 mmStrip width min / max: 10/1000 mmDistance between the consoles: 2530Height above the ground: 900 mmTable length without extension arms: 3030 mmOil volume: 800 lMax. Pressure: 280 barOperating voltage: 400VControl voltage: 230 V.Nominal current: 87 A.Weight: 15.8 toDimensions L x W x H: 3500 x 2500 x 2400 mmAccessories / special equipmentPneumatic cutting gap adjustmentCutting length limitationRoller conveyor elevation bracketHand protection 1 bayMultitron control Multitron PS 80, ELCO 85 PLower knife height adjust ...

规格： 切割宽度 3050 mm - 切割能力为 45 Kp/平方毫米 4 毫米 - 海德。切割角度调整 - 压持次数 18 个 - 冲程速率高达 24 /分钟 - 前角挡块 1100 mm - 3个前支撑臂750毫米 - 莫特。带定位控制的后挡风玻璃 5 - 1000 mm - 钣金支撑 - 切割线照明 - E – 脚踏开关 - 带光栅的后部空间保护 - 驱动 400 V / 9.5 kW - 空间要求约为 宽 3900 x 高 1850 x 深 2100 mm - 重量约 5.7 �

板材宽度：5000毫米板材厚度：6毫米支架宽度：5030毫� ��投影：340毫米机器重量约：14吨空间要求约：5500 x 2250 x 2200毫米此广告的数据fü，此广告是使用ModulMWS创建� �� - LogoTech oHG的机器管理�

sheet width: 3100 mmplate thickness: 10 mmrear stop: 1000 mmthroat: 350 mmcutting angle: 2,0 °down holder: 14 Stkno. of strokes: 13 Hub/mintotal power requirement: 22 kWdimensions of the machine ca.: 4050 x 2500 x 2170 mmweight of the machine ca.: 10575 kg-------------------------------------------------- ---------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------- ---------Furnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer cuts- 1x s ...

sheet width: 3100 mmplate thickness: 10 mmrear stop: 1000 mmthroat: 350 mmcutting angle: 2,0 °down holder: 14 Stkno. of strokes: 13 Hub/mintotal power requirement: 22 kWdimensions of the machine ca.: 4050 x 2500 x 2170 mmweight of the machine ca.: 10575 kg-------------------------------------------------- ---------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------- ---------Furnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer cuts- 1x s ...

sheet width: 3100 mmplate thickness: 10 mmrear stop: 1000 mmthroat: 350 mmcutting angle: 2,0 °down holder: 14 Stkno. of strokes: 13 Hub/mintotal power requirement: 22 kWdimensions of the machine ca.: 4050 x 2500 x 2170 mmweight of the machine ca.: 10575 kg-------------------------------------------------- ---------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------- ---------Furnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer cuts- 1x s ...

sheet width: 2100 mmplate thickness: 6 mmrear stop: 1000 mmcutting angle: 1,2 °down holder: 11 Stkno. of strokes: 28 Hub/minoil volume: 150 ltotal power requirement: 11 kWdimensions of the machine ca.: 3010 x 2100 x 1640 mmweight: 4500 kg Available from stock-------------------------------------------------- ---------electrical / hydraulic CNC swing cutting shear with CYBELEC CNC touch screen control with electric / hydr. Cutting gap adjustment-------------------------------------------------- ---------Furnishing:- CNC electrical / hydraulic swing cutting shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material selection, including sheet thickness Cutting line lighting- motorized back gauge, travel = 1,000 mm (X axis) on ball screws automatic Can be folded up at maximum travel ...

sheet width: 3100 mmplate thickness: 6 mmrear stop: 1000 mmcutting angle: 1,2 °down holder: 14 Stkno. of strokes: 18 Hub/mintotal power requirement: 11 kWdimensions of the machine ca.: 4.000 x 2.100 x 1.640 mm-----------------------------------------------------------electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-----------------------------------------------------------F urnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. can be folded up at max.travel, for longer cuts- 1x side stop- 2x front support arms- Ball rollers in the f ...

sheet width: 3100 mmplate thickness: 6 mmrear stop: 1000 mmcutting angle: 1,2 °down holder: 14 Stkno. of strokes: 18 Hub/mintotal power requirement: 11 kWdimensions of the machine ca.: 4.000 x 2.100 x 1.640 mm-----------------------------------------------------------electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-----------------------------------------------------------F urnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. can be folded up at max.travel, for longer cuts- 1x side stop- 2x front support arms- Ball rollers in the f ...

控制赛贝莱克 ...DNC 60 切割长度...2600 毫米 板材厚度...8毫米 驾驶。。。水力的 长 x 宽 x 高 ...3550x2020x1850毫米 机器重量...6200公斤 主机功率15千瓦 机器状况良好，可在断电下进行测试�

sheet width: 3100 mmplate thickness: 6 mmrear stop: 1000 mmthroat: 350 mmcutting angle: 0,5 - 1,5 °down holder: 14 Stkno. of strokes: 16 - 24 Hub/mintotal power requirement: 11 kWdimensions of the machine ca.: 4100 x 2200 x 2190 mmweight of the machine ca.: 7060 kg-------------------------------------------------- ---------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------- ---------Furnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer c ...

sheet width: 3100 mmplate thickness: 6 mmrear stop: 1000 mmthroat: 350 mmcutting angle: 0,5 - 1,5 °down holder: 14 Stkno. of strokes: 16 - 24 Hub/mintotal power requirement: 11 kWdimensions of the machine ca.: 4100 x 2200 x 2190 mmweight of the machine ca.: 7060 kg-------------------------------------------------- ---------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------- ---------Furnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer c ...

FASTI 断头台剪 有效长度：1030mm 最大板材厚度：2.5mm

sheet width - max.: 2035 mmplate thickness: 6.0 mm STplate thickness: 4.0 mm VAplate thickness: 8.0 mm ALUnumber of strokes - loaded: 20 Hübe/mincutting angle: 1.7 °work height max.: 900 mmNumber of working hours: 1.450 hControl: LENORD total power requirement: 11.0 kWweight of the machine ca.: 4100 kgrange L-W-H: 2416 x 2250 x 1760 mm Machine from prototype construction Machine with only approx. 1.450 operating hours ()Furnishing:- electro-hydraulic guillotine shears- electro-motorized backgauge with NC control unit (Lenord + Bauer)- electrical cutting length limitation- manual cutting gap adjustment- 1x stable side stop, with scale and tilting cam- 2x front support arms- 1x freely movable foot switch- Operating instructions (PDF) + circuit diagram Special accessories included:- pneumatic sheet metal holding device for thin sheet metal cuts Machine link:http://mhp.logotech.de/hpm/v7/D ...

切割长度： 3040 mm 板材厚度： 4 毫米钢 电动后规，带最大 1000 mm 的数字显示 侧挡块和工作台长度 切割长度限制 切割边缘照明 重量约 4500 kg

板材宽度： 3000 mm 板材厚度： 10，00 mm 柱间距离： mm 总功率要求： kW 机器重量 约： 10，00 t机器尺寸： 3，60 x 2，50 x 2，05 m• 受控后挡径 10 - 1000 mm• 角度挡块 1600 mm• 3 个额外的支撑臂• 自动切割间隙调整• 自动切割角度调整• 切削刃照明• 切割长度限�

最大工作长度 2，500 mm板材厚度 6 mm，气动压紧，电动背切，重量 6，400 kg

板材宽度： 4000 mm 板材厚度： 4，00 mm 柱间距：毫米 总功率要求：kW机器重量 约： 8，50 t机器尺寸：m可控后挡径可达 1，000 mm侧挡块和工作台扩展切割长度限制尖端照明防护围� �，可卷曲，带安全开�