二手 PEMA 出售

PEMAMO MDR 120E卧式珩磨机由瑞士PEMAMO珩磨公司于2002年制造。该� �器用于专门珩磨孔，例如活塞气缸，以实现所需的尺 寸，公差和高表面质量。得益于珩磨机，可以消除形� ��缺陷，如划痕、轴曲率或波纹。 珩磨机使用每分钟旋转310至1860次的主轴对直径从1.5 mm到40 mm的孔进行精加工。卧式珩磨机配有AR 340半自动膨胀装置，重复精度为1 μm。机器的总重量约为135公斤。 德国医学博士 120E 珩磨机的技术数据 - 最小珩磨直径：1.5毫米 - 最大珩磨直径：40 mm - 主轴转速：310-1860 rpm - 半自动扩充单元：AR 340 - 启动/停止脚踏开关 - 冷却系统 - 集成珩磨油容器容量：15升 - 装机功率：0.5千瓦 - 电源： 3x 400V;50赫兹 - 机器尺寸（长 x 宽 x 高）： 900 x 400 x 500 mm - 重量：约135公�

卧式镗床 / 开槽钻孔机 / 完好无损，可立即使用，立即可用 这款 PEMAL MALBORK 的 DWLA 型长孔钻床刀具直径为 10 mm，最大孔深为 160 mm，是精密和苛刻作业的理想选择。 规格： - 刀具直径： 10 mm - 最大孔深：160 mm - 最大铣刨长度：160 mm - 调整方式：带前/后钻孔装置 - 工作台调整：上/下和侧向 - 工作台旋转角度：+/-20° - 工作台尺寸： 620 x 280 mm - 电机功率：1.5 kW - 尺寸：长/宽/高1120 x 830 x 1200毫米 - 重量： 300 kg 通过前/后钻孔装置进行调整以及工作台调整选项，提 供了最大的灵活性。 工作台可以旋转 +/-20°。 该机器处于一流的状态，可以立即使用。凭借其精确� ��设计和强大的电动功能，它非常适合在各种应用中� �行精确工作。 机器可以随时查看。 价格不� ...

滚架支架辊床 制造商： 佩玛 / 欧莎宝 类型：3 个 TXA / 3 个 TXN（1 个单元） 建设年份： 2008 最大负载/截面： 1.5 吨 / 1.5 吨 最大推力 F： 3 kN 轧制速度范围：60 – 1200 毫米/分钟 固定中心高度： 434 – 800 mm 总直径范围 最小-最大： 106 – 2179 mm 钢卷件/段： 2 件 滚筒直径/总宽度： 350 / 80 mm 电源电压：230 V – 1 相 – 50 Hz/16 A 长度： 1690 mm / 1445 mm 宽度： 670 毫米 / 570 毫米 高度： 615 – 878 mm / 610 – 878 mm 重量： 480 公斤 / 420 公斤 遥控器 / 电缆长度： RC31H / 6m

供应信息 23348 规格： - 最大负载能力 1500 Kg - 面板直径 850 mm - 从地板到中心旋转轴的距离 800 mm - 旋转运动电动器。无级可调 0.08 - 1.6 rpm - 右 - + 左 - 运行 - 焊接电流传输约100000000000000000000000000 700 安培 - 驱动 400 V / 2.2 kW - 空间要求单位约。 宽 850 x 高 1450 x 深 1000 mm - 空间要求：移动单元宽 850 x 高 1450 x 深 1000 mm - 从动单元重量约100 550 千克 - 移动单元的重量约定 400 千�

库存号： 3871 焊接转盘 制造商： ESAB PEMA， 型号： 3500 F 机器编号： A7001， 制造年份： 1987 规格： 工作台尺寸 1500 mm Ø 大工件重量 3500 kg Gr. 旋转扭矩 3100 NM 无级可变的工作台旋转。 0.01 - 0.8 公关/分钟 液压驱动装置和尖端 长度： 2000 mm， 高度： 1100， 宽度： 1500 mm， 重量： 1200 kg

带旋风工具的行星式搅拌机，2颗搅拌星，4个搅拌刀� �和刮刀/空桶。每批最大填充量：2，250 l. / 3，600 kg，每批硬化混凝土产量：1，500 l.，可加工粒度：0 - 65 mm，带双面旋转滑块出口（液压操作）。 包括 75 kW 的主驱动电机和许多备件�

带旋风器工具的行星式搅拌机，2个搅拌星，4个搅拌� �和刮刀/卸料铲。每批最大产能：2.250 升/3.600 千克，每批硬化混凝土产量：1.500 升，可加工粒度：0 - 65 毫米，带双出口（液压操作）。 包括主驱动 75 kW 和许多备件�

sheet width: 2050 mm plate thickness: 3 mm strokes per minute until: 35 cutting angle: 2,0 ° table height over floor: 870 mm thickness at Niro-steel: 2 mm total power requirement: 4 kW weight of the machine ca.: 1550 kg range L-W-H: 2,5 x 1,57 x 1,21 m Electric 380 Volt: The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with a Standard geared brake motor via a chain connection to the main axle. the Knives are of the highest quality. The optimal cutting angle secures the Together with the rubber-covered blank holder perfect cuts. Bearings and guides are maintenance and lubrication-free. Standard equipment: • Back gauge 665 with mm scale. • cutting edge lighting. • Section counter. • Table extensions 600 mm. • Right angle stop, left. • Movable 24 V foot switch with emergency stop. • Motor protection switch and ...

bore capacity in steel (diameter): 25 mm throat: 255 mm bore stroke: 135 mm spindle turning speed range: 8, von 105-2900 U/min table-size: 500 x 350 mm column diameter: 100 mm spindle taper: MK 3 total power requirement: 0,65 / 0,9 kW weight of the machine ca.: 190 kg dimensions of the machine ca.: 0,5 x 0,5 x 1,7 m Electric 380 Volt: Drill chuck: Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1275 mm plate thickness: 3 mm strokes per minute until: 35 cutting angle: 2,0 ° table height over floor: 870 mm thickness at Niro-steel: 2 mm total power requirement: 3 kW weight of the machine ca.: 875 kg range L-W-H: 1,7 x 1,68 x 1,1 m Electric 380 Volt: Back stop with manual adjustment: Shadow line lighting: Foot switch: Piece counter: Squaring arm: Support arms: The guillotine shears type SMP is a well-dimensioned machine with all-welded gate guides. The drive takes place with a standard geared brake motor via a chain connection to the main axis. The knives are of the highest quality. The optimal cutting angle ensures together with the rubber-coated sheet metal holder, perfect cuts. Bearings and guides are maintenance-free and lubrication-free. Standard equipment: • Back gauge 635 with mm scale. • Cutting line lighting. • Section counter. • Table extensio ...

bore capacity in steel (diameter): 40 mm throat: 297 mm bore stroke: 120 mm speeds: 8 / 75 - 1600 U/min table-size: 500 x 460 mm spindle taper: MK 4 column diameter: 115 mm spindle feeds:: 3 / 0,1 - 0,26 mm/U distance spindle /table: 715 mm distance spindle/base plate: 1180 mm engine output: 1,5 kW table rotating: 360 Grad weight of the machine ca.: 335 kg dimensions of the machine ca.: 0,5 x 0,76 x 1,89 m Electric 380 Volt: Cooling pump in machine base: Machinelight: Heavy geared boring machine with digital display for speed and drilling depth, hardened gears, thick-walled column, large table and base plate with T-slots, motorized table adjustment, electromagnetic feed engagement by means of snaps on the control lever. Machine not much used from the demonstration area. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution  ...

sheet width: 2020 mm plate thickness: 2 mm daylight upper clamping: 122 mm bending angle max.: 135 ° range L-W-H: 2,56 x 0,6 x 1,26 m weight of the machine ca.: 1020 kg Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

板材宽度：1020 mm 板材厚度：2.5 mm 支架宽度：1045 mm 开口宽度：最大 47 mm 弯曲角度 最大： 135 机器重量约： 290 kg 空间要求约： 1.35 x 0.86 x 1.17 m 用于弯曲箱型材的分段式顶轨，最大边缘高度约为 64 mm，上脸颊夹紧脚踏，手动弯曲脸颊驱动 ，可调节弯曲停止，通过 调整弯曲脸颊改变弯曲半径。保修期 = 12 个月。 弯曲性能是指强度为380 N/mm²的板材。 仓库管理员，展厅面积为2500平方米。 该广告的数据是使用模态MWS创建的 - 标识科技oHG的机器管理。

sheet width: 2050 mm plate thickness: 2 mm strokes per minute until: 38 cutting angle: 1,75 ° table height over floor: 870 mm total power requirement: 3 kW weight of the machine ca.: 1520 kg range L-W-H: 2,2 x 0,6 x 1,2 m Electric 380 Volt: Back stop with manual adjustment: Shadow line lighting: Foot switch: The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with a Standard geared brake motor via a chain connection to the main axle. the Knives are of the highest quality. The optimal cutting angle secures the Together with the rubber-covered blank holder perfect cuts. Bearings and guides are maintenance and lubrication-free. Standard equipment: • Back gauge 665 with mm scale. • cutting edge lighting. • Section counter. • Table extensions 600 mm. • Right angle stop, left. • Movable 24 V foot switch with emerge ...

With accessories, an inspection is possible.

General SKU383U1043 LocationBarneveld MakeNetzsch TypeMastermill 3 No.2404563 Year of construction2015 Main Features MaterialStainless steel Volume10 Ltr. Motor2.2 KW Specified Features - Sand mill MaterialPlexiglass/acrylic glass, Stainless steel 1.4552 Vertical sandmillcheck Basket Mill Capacity9 Ltr. Housing dimensions Dia. 220x250 mm InletDia. 220 mm With sievecheck With jacketcheck Motor2,2 kW With variable speed drivecheck frequency converter Rotor speed1100-3000 rpm With ballscheck Information With switchgearcheck (as is) Total height1,2 m Weight630 kg CEcheck Floorspace1,2x0,9 m ATEX compatiblecheck Extra SpecificationsDrive power mill, 2,2 kW, drive power stirrer 0,75 kW, mill speed 1100-3000 rpm, mixer speed 180-2600 rpm, basket volume 0,5 ltr, :Sand millsNetzschMills > Sand millsBrand > Netzsch What you can expect from Foeth: -- Machine is in wo ...

General SKUR0090 LocationBarneveld MakeSchröder & Co (D) Typemanufacturer plate is missing No.30-392 Main Features MaterialStainless steel Volume2 Ltr. Motor2.2 KW Specified Features - Scraped surface heat exchanger Capacity2 Ltr. Inletdia. 25mm Outletdia. 25mm With motor2.2 kW 230 Volt With variable speed drivefrequency controller Scraped surface heatexchangers MaterialStainless steel Cylinder sizesdia. 95x350mm Inletdia.25mm Outletdia.25mm Motor2,2 kW 230 Volt With variable speed drivefrequency controller Information Mounted on wheelscheck With switchgearcheck Floorspace1,3x0,4 M Total height1,4 M Weight260 KgScraped surface heat exchangersSchröderHeat exchangers > Scraped surface heat exchangersBrand > Schröder What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destinatio ...

General SKU232S114 LocationBarneveld MakeTerlet (NL) TypeMaxxitherm No.0410143 Year of construction2005 Pressure Working pressure5 Bar Working pressure jacket4 Bar Main Features MaterialStainless steel Motor1.1 KW Surface7.5 m2 Specified Features - Scraped surface heat exchanger MaterialStainless steel 1.4404 (316L) Scraped surface heat exchangercheck Number of stages:1 Heating surfaceca 7.5 m2 Heating surface shellinner wall ca. 3.5 m2 outher wall ca. 4 m2 Cylinder sizesouther wall dia. 560x2400mm (1x), inner wall dia. 500x2400mm (1x) Max. temperature-10/100 degr. C With jacketcheck Max. temperature153 degr. C InletDN80 OutletDN80 Motor1.1 kW 220-240/380-415 Volt Speed1,4 rpm Information Mounted on framecheck Mounted on wheelscheck Total height2.1 M Weight2100 Kg CEcheck Floorspace4.0x1.2 M Extra SpecificationsThe Maxxitherm brings about a continuous  ...

General SKU243P325 LocationBarneveld MakeUnknown Typemanufacturer plate is missing Main Features MaterialStainless steel Volume1200 Ltr. Motor15 KW Specified Features - Ribbon blender Ribbon blendercheck Capacity1200 ltr Useful capacity1000 ltr Trough sizesdia. 1000x1500 mm Inlet1500 x 440 mm Outletdia. 100 mm Interrupted ribboncheck With adjustable packing glandscheck Motor15 kW 380/660 Volt Speed mixing shaft30 rpm MaterialStainless steel Information Floor space3,1x1,5 m Total height1,8 m Weight2100 kgRibbon blenders-Mixers > Ribbon blendersBrand > - What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKULT004 LocationGermany MakePharmatec GmbH/ Syntegon Technology / Pepperl+Fuchs TypeMain Fraction Tank No.12462 Year of construction2021 Pressure Working pressure3 Bar Vacuum possiblecheck Working pressure jacket6 Bar Vacuum possible jacketcheck Main Features MaterialStainless steel Volume20.5 Ltr. Motor0.09 KW Specified Features - Stainless Steel Reactor Reactorcheck Capacity15,0 Ltr (20,5 Ltr ) Vessel sizesdia,250 x315mm Outlet3/4 With jacket(4,5 Ltr, 0,19m2) Max. temperature-10/95 degr.C. With propellor stirrerMagnetic ZETA, Type BMRT 50 W EX S Dk Motor0.09 kW, 230-400 Volt, (Ex) Speed mixing shaft125-860 rpm Stainless Steel Reactors MaterialStainless steel 1.4404 (316L) Information With switchgearcheck Total height+/- 1,5 M2 CEcheck Mounted on legsmobile skid With switchcheck ATEX compatiblecheck Extra Specifications- The tank is equipped  ...

General SKU271S307 LocationBarneveld MakeDMN Westinghouse Machinefabriek (NL) TypeMALD200 1 No.990510 / 40821 Year of constructionunknown Main Features MaterialMild steel Motor0.55 KW Inlet diameter200 mm Specified Features - Rotating valve MaterialMild steel Rotary valvecheck Rotor width260mm Number of locks:8 Lock sizes260x90x100mm Inletdia. 200mm Inlet flange sizesdia. 345mm stc 295mm Outletdia 200mm Outlet flange sizesdia. 345mm stc 295mm Installation height400mm With motor0,55 kW 230/400 Volt Rotor speed140 rpm Air purged sealingscheck Information Total height0,4 M Weight100 Kg Floorspace0,6x0,6 MRotating valvesDMN MachinefabriekRotary valves > Rotating valvesBrand > DMN Machinefabriek What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welc ...

General SKU300U1181 LocationBarneveld MakePanametrics TypeMagnamike 8000 No.97299607 Year of construction2017 Specified Features - Miscellaneous Motor220 volt Information Total height0,15 m Weight4,6 kg Floor space0,31x0,26 m Extra SpecificationsWall thickness measuring Comes with tooling, Measuring range bullet diameter 1,6-9,6mm, 0-10,2mm MiscellaneousPanametricsMiscellaneous > MiscellaneousBrand > Panametrics What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

second hand welding toner Brand: PEMAMEK OY Model: 60TS Power: Three-phase 380V Crazy turner + motorized turner Diameter range (Minimum - Maximum): 900 - 5200mm Translation for motorized tacking movement Type: Self-aligning Command with movement control and regulator for rotational speed variator Year 2000 Weight: 1990kg

技术数据 电压 50 Hz 3x： 380 V

工件重量： 0 kg 工件直径 最大： 0 mm 工件直径 最小： 0 mm 卷筒数量： 0 MACH-id   3597 让 埃萨布佩玛芬兰 类型  60 TS 1997年