制造商: 海默勒 型号: TRM 50/750 建造年份: 1990/ 2023 大修:2023 年 板材宽度:最大 750 mm 片材厚度: 约 0.5-12 毫米 流动方向的零件长度:最小约100mm 进给速度:2-20米/分钟 矫直辊数量:19个 直径:50毫米 工件入口高度:900mm 功率要求:31kW 总重量:约10.000公
液压折弯和压花压力机,二手,动力下 液压压花压力机/折弯机,使用,动力下 Fabr./ make: 海默尔 型号/型号:2S 100-2050 建设年份/ 年份: 1978 冲压力: 100 t 操作长度: 2050 mm 滑枕调节: 150 mm 距餐桌的距离/ 滑枕到工作台的距离: 400 mm 行程: 150 mm 最大接载: 11 kW 重量: 5.9 t
规格: - 压力容量 2000 kN - 最大工作宽度 3100 mm - 支架通道 3200 mm - 立柱放电 300 mm - 最大安装高度 965 mm - 行程或偏移深度无级可调 0 - 400 mm - 冲压速度前进 + 返回每 100 毫米/秒 - 工作速度可在9个步骤中选择 1 - 10 mm/sec - 驱动 400 V / 26.5 kW - 空间要求约为 宽 4400 x 高 3500 x 深 2200 mm - 重量约 18500公斤 - 与: - CNC - 控制赛贝莱克ModEva 15S制造于2007年 - 后备考格与4个受控的肺。侧面的 和高度可调的停止手指 - 停止区域中受控的弯曲辅助装置 - 海德。- 肺。上部刀具 + 下部刀具的夹紧 - 莫特。表冠/水力垫 - 横向可移动的支撑臂 - E - 脚踏开关 - 剖分式刀具 R 1-100 t/m,分体式模
Ref.nr. 00766 工厂描述 二手折弯机 制造商: 海默勒 M+S 布鲁格股份公司 型号 AP 100 – 2100 建造年份:1991年 最大压力 1000KN 最大工作长度 2100mm 最大行程 400mm 投影 300mm 质量重量 11500kg 工作电压 380V 50Hz 控制电压 24V 总连接数 23 KW 备用保险丝的标称电流 63 A
编号 00785 工厂描述: 二手折弯机 制造商: Hämmerle 型号 AP 200 – 3600 建成于 1991 冲压力 2000KN (200 T) 准备工作 3600mm 最大行程 400mm 投影 500mm 击键 6 控制 DNC 7000 装机功率 18.5kW 重量 21,000 kg 工厂通电状况 立即提交日期 除了机器之外,还可以购买多种工具。
Description: maximum pressing force 175 t, maximum stroke 300 mm, throat 300 mm, ram distance 700 mm, working length 2050 mm weight approx.: 12,000 kg, Approx. Onsite Dimension. (l x w x h): 4,800 x 2,200 x 3,300 mm
压力:2000 kN 弯曲长度:3100 mm 支架宽度:3240 mm 控制:Infinitron 冲压行程:400 mm 工作高度:1104 mm 投影:250 mm 工作宽度:160 mm 流速:160 mm/s 工作速度:1-10 mm/秒 返回速度:160 mm/sec 油箱容积:550 l 总功率要求:28 kW 机器重量约:16.6 t 空间要求约:4.4x2.7x3.4 m CNC 控制 Infinitron 水垫 MHK 1-30 三点矩阵支架 DH 1-30 停止系统 A2,行程范围 600 mm 通过单独 控制的 Z 轴 钣金支撑系统沿止动梁调整停止滑块 H 2 通过单独控制的 W 轴 控制台 SK 10 与提升辅助装置 0-45 与直线导轨 调整各个钣金支撑控制台 本广告的数据是使用 ModulMWS 创建的 - LogoTech oHG 的机器管理。
pressure: 200 t chamfer lenght: 3100 mm distance between columns: 2780 mm Control: Addcobend Infinitron total power requirement: kW weight of the machine ca.: 18 t dimensions of the machine ca.: m CNC control: Addcobend Infinitron Press force: 2000 KN Bending length: 3100 mm Distance between columns 2780 mm Clear distance between columns 2780 mm Projection of the stands 300 mm Back gauge - adjustable 1600 mm Stroke max. 400 mm Space required length 4300 mm Space requirement width 2650 mm Total height 3800mm Total weight about 18000 kg Machine hours 2011: 21226 h Machine hours today: approx. 23000-25000h Retrofit: 2011: approx. CHF 86,000 • Basic remodeling • Exchange Axodyn controller units (X & M axis) • Replacement of control relays and Telemecanique PLCs with safety PLCs • Replacement of power relays and thermal overcurrent trips • Double foot switch with additional functi ...
Max. pressing force: 2000kN, max. working length: 2600mm, max. stroke: 265mm, throat depth: 300mm, weight: 16t.
Max. pressing force: 1000kN, max. working length: 3100mm, throat depth: 250mm, connected load: 18kW, weight: 9.5t, operational hours counter: 76,566h, with accessories and documentation, was maintained regularly.
Max. working width: 3100mm, max. stroke: 400mm, max. pressing force: 2000kN, weight: 16.6t.
Consistent precision when bending due to 3-point technology and pressure distribution via hydro cushion. Very good maintained condition. Has always been serviced regularly and annually by the company Bystronic (service reports are available). Servomotors were exchanged. Still some spare or wear parts new with it.