二手 GILLARDON 出售

供应 23010 规格： - 钻孔能力 20 mm - 钻孔主轴支架 MK 2 - 钻孔主轴行程 140 mm - 钻孔主轴转速无级变速 150 - 3000 rpm - 投影 285 mm - 色谱柱直径 105 mm - 最小/最大距离钻孔主轴/工作台 245 / 675 mm -照明 - 快速动作卡盘 - 冷却液装置 - 机器台虎钳 - 机器底盘系统 - 驱动 400 V / 0.5 / 0.9 kW - 尺寸 宽 600 x 高 1900 x 深 900 mm - 约重 200 公�

供应 23036 规格： - 实心钢 ST 60 32 mm 的钻孔能力 - 钻孔能力 GG 25 40 mm - 螺纹切割 ST 60 M 27 - 钻孔主轴支架 MK 4 - 鹅毛笔行程 150 mm - 12 钻孔主轴转速 102 - 2000 rpm - 3 个钻头进给 0.1 - 0.3 mm - 主轴最小/最大距离 – 工作台 310 / 610 mm - 钻孔半径最小/最大 400 / 1200 mm - 工作台高度 720 mm - 工作台尺寸 1200 x 500 mm - 驱动 400 V / 1.6 / 2.9 kW - 大约需要空间 宽 1200 x 高 2800 x 深 2300 mm - 约重 1500 公斤 - 带： - 攻丝装置 - 水力。立柱 + 动臂夹具 - 冷却液装置 - T – 机器后侧垂直凹�

供应 22493 规格： - 钢 ST 60 40 mm 的钻孔能力 - ST 60 50 mm 钢的钻孔能力 - 攻丝采用 ST 60 至 M 42 钢制成 - 钻孔主轴支架 MK 4 - 钻孔主轴行程 200 mm - 钻孔主轴转速无级可调 60 – 1100 rpm - 右 - 左旋转 - 3 个进给 0.1 / 0.16 / 0.25 毫米/转 - 投影 350 mm - 长距离钻孔主轴 – 工作台 / 底板 790 / 1210 mm - 带 2 个 T 型槽的工作台 630 x 540 mm - 通过带手摇曲柄的机架调节高度 - 驱动 400 V / 1.8 / 3.5 kW - 大约需要空间 宽 600 x 高 2050 x 深 980 mm - 约重 650 公斤 - 带： - 紧急停止按钮 - - 照明 - 快速更换钻卡盘 1 - 13 mm - 冷却液装置 - 机床虎钳 - 20 件高速钢 – 麻花钻 8 – 20 mm

规格： - ST 60 钢钻孔能力 32 mm - 钻孔能力 ST 60 40 mm - 钻孔主轴架 MK 3 - 钻孔主轴行程 175 mm - 12 个钻孔主轴转速 120 – 3000 rpm - 投影 290 mm 钻孔主轴与工作台/底板之间的距离 630 / 1190 mm - 带 2 个 T 型槽的桌子 570 x 475 mm 可通过带手摇曲柄的齿条和小齿轮调节高度 - 驱动功率 400 V / 1.1 / 1.8 kW - 空间要求约为 宽 600 x 高 1950 x 深 980 mm - 重量约 450公斤 - 与： - 机器台钳 - 快速释放钻头卡盘 1-13 mm - 照�

供应 23240 规格： - ST 60 32 mm 钢的钻孔能力 - 钢 ST 60 40 mm 的钻孔能力 - 攻丝装置高达 M 27 - 钻孔主轴支架 MK 3 - 钻孔主轴行程 175 mm - 钻孔主轴转速在 60 至 1600 rpm 之间无级变化 - 3 馈电。磁性压痕 0.1 ; 0,16 ; 0.25 毫米/转 - 投影 290 mm - 钻孔主轴与工作台之间的最大距离 790 mm - 与钻孔主轴的最大距离 - 底板 1210 mm - 带 2 个 T 型槽的桌子 570 x 475 mm - 通过带手摇曲柄的齿轮齿条可调节高度 - 桌子左+右倾斜 - 带增强型电机的驱动器 400 V / 1.6 / 2.9 kW - 大约需要空间 宽 600 x 高 1950 x 深 980 mm - 约重 450 公斤 - 带： - 底板上的冷却液装置 - 快速释放钻卡盘 1-13 mm - 紧急停止按钮 -照明 - 机器虎�

钢钻孔能力 45 mm 刀柄 MK 4 冷却液泵 顺时针和逆时针旋转 3种不同速度的电磁馈�

钢的钻孔能力 30 mm 刀架 MK 3 2 种不同的电机速度 带显示屏的无级变速调�

型号 R 25 作为 6 倍在线钻孔机 5个钻井单元： 16 速 90 – 1980 rpm 驱动功率 0.7 / 1.3 kW 刀柄 MK 3 ST60 钻孔能力 28 mm 立柱直径 105 mm 投影 280 mm 主轴行程 150 mm 高度调节 500 mm .

16 种速度 90 – 1980 rpm 驱动功率 0.7 / 1.3 kW 刀柄 MK 3 ST60 的钻孔能力 28 mm 色谱柱直径 105 mm 投影 260 毫米 主轴行程 150 mm T型槽板到主轴鼻端约： 最小 – 最大 240 - 620 mm 工作台离地高度 830 mm 机器最大高度约 2 米 钻头重量约。 0.15 至 设备/供货范围 ： T 型槽板，宽 x 深 = 800 x 700 mm，T = 50 mm

规格： ST 60 30 mm 的连续钻孔能力 12 个速度级别 60 – 2240 rpm 主轴马达 1.1 / 1.6 kW 半径约值 320 毫�

16 种速度 90 – 1980 rpm 驱动功率 0.7 / 1.3 kW 刀柄 MK 3 ST60 的钻孔能力 28 mm 色谱柱直径 105 mm 投影 280 毫米 主轴行程 150 mm

Description: Column drilling machine with: - Advance - variable spindle speed - Coolant pump - Machine light Drilling capacity in steel 32 mm Projection 320 mm Drilling stroke 170 mm Recording MK 4 MK Table size 570 x 480 mm Feeds 0.1 - 0.16 - 0.25 mm/rev Speed 60 - 1600 rpm Total power requirement 1.6 KW Machine weight approx. 0.65 t Dimensions L x W x H 1.2 x 0.8 x 2.15 m weight approx.: 650 kg, Approx. Onsite Dimension. (l x w x h): 1,200 x 800 x 2,150 mm

Description: Includes vice, jaw width 120 mm table surface area l x w : 560x440 mm, weight approx.: 500 kg, Approx. Onsite Dimension. (l x w x h): 1,100 x 800 x 2,200 mm

Description: Includes vice, jaw width 100 mm , turning speed range: 60 - 950 rpm, table surface area l x w : 320x320 mm, weight approx.: 300 kg, Approx. Onsite Dimension. (l x w x h): 850 x 600 x 1,800 mm

Description: Quill stroke 180 mm Speed range up to 1200 rpm Table 645 x 510 mm Right/left rotation Approx. Onsite Dimension. (l x w x h): 1,200 x 800 x 1,700 mm, weight approx.: 350 kg

bore capacity in steel (diameter): 32 mm throat: 320 mm bore stroke: 170 mm taper MK: 4 MK table-size: 570 x 480 mm feeds: 0,1 - 0,16 - 0,25 mm/U turning speeds: 60 - 1600 U/min total power requirement: 1,6 KW weight of the machine ca.: 0,65 t dimensions: 1,2 x 0,8 x 2,15 m Column drilling machine with: - Feed - variable spindle speed - Coolant pump - Machine light The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 25 mm bore stroke: 150 mm Short spindle: MK 3 T-Slots Amount - Width - Distance: 2x14x180 mm base plate: 380x390 mm turning speeds: 60-1400 U/min voltage: 380 V Year: 1977 0 no. of spindles available: 1 table surface - upper: 705 mm clamping surface (upper): 400 x 315 mm base plate: 135 mm bore spindle - and spindle ram diameter: 39,6 mm weight of the machine ca.: 320 kg dimensions of the machine ca.: 550x870x1900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Boring power: 32.0 mm bore capacity in cast iron: 40.0 mm spindle stroke: 175 mm morse taper: MK 3 Kurzspindel throat: 320 mm column diameter: 130 mm feed: 0.1 - 0.16 - 0.25 mm/U table:: 570 x 475 mm T-slots: 2 x 224 x 14 mm turning speeds: 60 - 1600 U/min threading: M 27 / M 36 total power requirement: 1.1 / 1.8 kW weight: 530 kg range L-W-H: 570 x 960 x 1950 mm Furnishing: - robust & stable machine construction - continuous speed adjustment - Thread cutting device up to M36 - Button for R/L running of the work spindle - extended machine column - Pole-changing drive motor - automatic spindle feed - One-hand feed engagement - adjustable drilling depth stop - Work table height adjustable using hand crank - machined base plate - 3x MK tapping quick-change chucks - separate coolant device - EMERGENCY stop button at the front - User manual (PDF) Machine link: https://mhp.logotech.de/hpm/v7/ ...

Boring power: 35.0 mm bore capacity in cast iron: 40.0 mm Center of spindle to wall or column: 345 mm bore stroke: 170 mm Size of table plate: 600 x 500 mm Speed: 40 - 1250 U/min. spindle taper MT: 3 MK feed: 0.1 - 0.16 - 0.25 mm/U voltage: 400 V Motor output: 1.0 / 1.5 KW weight of the machine ca.: 425 kg range L-W-H: 1000 x 650 x 2150 mm Furnishing: - robust & stable machine construction - continuous speed adjustment - extended machine column - Pole-changing drive motor - automatic spindle feed - One-hand feed engagement - adjustable drilling depth stop - Work table height adjustable using hand crank - Taper mandrel including keyless drill chuck Machine link: https://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=100 8-9103746 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Boring power: 40.0 mm bore capacity in cast iron: 50.0 mm morse taper: 4 Kurzspindel MK spindle stroke: 200 mm throat: 360 mm column diameter: 160 mm feed: 0.1 - 0.16 - 0.25 mm/U distance spindle/base plate: 1200 mm T-slots: 2 x 224 x 18 mm table:: 630 x 530 mm speeds: 60 - 1600 U/min total power requirement: 1.4 / 2.3 KW weight: 620 kg range L-W-H: 630 x 985 x 2020 mm Furnishing: - robust & stable machine construction - continuous speed adjustment - Pole-changing drive motor - electro-magnetic automatic spindle feed - One-hand feed engagement - adjustable drilling depth stop, with fine adjustment - Work table height adjustable using hand crank - machined base plate, including coolant system - Foot switch for function: spindle off - User manual (PDF) Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9103745 The data for this ad was created with Modu ...

table length: 760 mm table width: 425 mm groove width: 22.0 mm weight: ca. 85.0 kg current new price approx. 5.000 euros Special price on request Furnishing - robust / solid cross table - from a GILLARDON column drill - machined clamping surface 600 x 325 mm - Longitudinal displacement 400 mm - Transverse displacement path 200 mm Link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -980272 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.