| 描述: |
插齿机 GLEASON- PFAUTER P 1200 S
二手机
max. wheel diameter: 1200 mm
gear width: 350 mm
max. module:
16
min. module: 0,5
max. workpiece diameter: 1400
mm
table diameter: 1200 mm
table hole: 300 mm
control:
Siemens 840D Powerline
total power requirement: 75 kW
weight
of the machine ca.: 24 t
dimensions of the machine ca.: 5x3x3,8
m
Gleason-PFAUTER CNC gear shaping machine P 1200 S for the
production of
internally and externally cylindrical gears with
internal and external teeth
and other rolling profiles and moulds
profiles and moulds that regularly occur
on the cylindrical
workpiece circumference and for the production of profiles
in the
single part process.
Special version with hydraulic shaping
head H1
SCOPE OF EQUIPMENT:
- Basic machine P1200S,
Siemens 840D Powerline (XP)
- Hydraulic shaping head H1
-
Signal light (3-colour)
- Extended software for fault
diagnosis
- Telephone diagnosis system
- Chip disposal through
table bore
- Set of adjusting wedges
- Monitoring
devices
- Warm-up programme
- Network connection
(Ethernet)
- 19 flat control panel OP 015A
- Offline version
dialogue programming
- Vapour separator make 3nine type
KLARA
- Machine installation under floor
- Rinsing gun
-
Mounting device
- Cutting wheel holder ( 3 pieces )
- Cutting
wheel holder for sheep cutting wheels
- Cutting wheel holder for
sheep cutting wheels
- Special cutting wheel holder
-
Preparation for retrofitting paper belt filter system
- Measuring
device for machine P 1200 S
- Clamping base body
- BDE/MDE
interface in the machine control cabinet
Modification of vapour
separator make 3nine type Klara type EMMA
Working range and
technical data:
Nominal workpiece diameter
External
toothing. . . . . . . . 1.200 mm
Internal gearing. . . . . . . .
1.200 mm
Largest workpiece circulation Ø without counter
stand... 1.400 mm
Nominal machine module approx.
- with
hydraulic impact head H1... 16 mm
Shaping spindle stroke
rate range
- with hydraulic shaping head H1 max. 80
min-1
Largest toothing width
- with hydraulic shaping
head H1... 350 mm
Smallest pitch height of the hydrostatic
screw guide
- with hydraulic shaping head H1... 850
mm
Smallest/largest distance between tool and workpiece
axis
- with hydraulic shaping head H1... 0 - 750
mm
Axial slide adjustment range - with hydraulic shaping head
H1... 1.100 mm
Lowest shaping spindle position above table with
hydraulic shaping head H1
with upper E632339 position Shaping
stroke... 560 mm
Column side offset range - with hydraulic
pusher head H1... +/- 50 mm
Mould mounting cone - with hydraulic
shaping head H1
- HSK-80(hollow shank taper according to DIN
69063)
Workpiece with external gearing:
- Module max. 16
mm,
- max. toothing width 350 mm,
- max. external Ø 1.200 mm,
Workpiece with internal gearing:
- Module max. 16 mm,
- max. toothing width 350 mm,
- max. circulation Ø 1.400
mm,
- max. internal Ø 1.200 mm,
- max. shaping wheel Ø 260
mm,
- Mounting in shaping spindle HSK-80,
- Slide travel,
X/Y/Z- 750 /100 / 1.100 mm,
Workpiece table:
- Outer Ø
1.200 mm,
- bore 300 mm,
- max. load 150 kN,
- Cooling
unit, Küma, type OWT600-3KK, year 2008,
- Hydraulic unit,
manufactured by Parka,
- Centrifuge, made by Steimel,
- Air
filter, Indusa, type EL4001NTDASECL/O,
version AOO, max. air
capacity 4.000 m³/h
The data for this ad
was created with ModulMWS - the software solution of LogoTech
oHG.
seller offer No. resale 1058-E23259
|